T-1000B Sd Card Led Pixel Controller Programmable SPI Signal Output
Full Color Dimmer
一 T-1000B System features,
1. 32~256 grade Gray level,Support software Gamma correction.
2. Support the rules and special-shaped handle.
3. 1 port output,can support 2048 lamp pixels.
4. SD Card control,offline control, the contents of the line
control program stored in the SD card..
5. T-1000B store 16 files max, copy the files into SD card in
turns.
6. Files be stored in the SD named as:00_1.led, 01_1.led, 02_1.led.
7. Compatible with single line or double line chips. Do not need to
connect CLK line when use single line led fixture.
Note: 1. When the port of T-1000B is loaded with 512 lights, the
playback speed can reach 30 frames/SEC. When the port is loaded
with more than 512 lights, the frame frequency will increase
The number of lights increases and automatically decreases
二 Supported chips,
| Supported chips | LedEdit Corresponding to the model | Max load lights |
| TM1803,TM1804,TM1809,TM1812 | T-1000B-TM1803 | 2048 |
| UCS1903,UCS1903B ,UCS1909,UCS1912 | T-1000B-UCS1903 | 2048 |
| UCS2903,UCS2909,UCS2912 | T-1000B-UCS2903 | 2048 |
| P9813 | T-1000B-P9813 | 2048 |
| WS2811 | T-1000B-WS2811 | 2048 |
| SM16726 | T-1000B-SM16726 | 2048 |
| SM16716 | T-1000B-SM16716 | 2048 |
| LPD6803,D705,1101 | T-1000B-6803 | 2048 |
| TM1903,TM1904,TM1909,TM1912 | T-1000B-TM1903 | 2048 |
| TM1914 | T-1000B-TM1914 | 2048 |
| P9883 | T-1000B-P9883 | 2048 |
| WS2801,WS2803 | T-1000B-WS2801 | 2048 |
三 Prints .
| Keypad | Meanings |
| 保存 SET | Save the Settings (if press SET key, the current Settings file and
playback speed will be saved, and press this to play again after
the next boot). |
| 模式 MODE | Switch files |
| 速度 SPEED+ | Speed up | Press Speed + and Speed - at the same time to enter the file
looping mode |
TTL signal(245signal)
| CKL | Clock line | DC5-24V | 5V power input |
| DAT | Data line | 电源灯POWER | Power light |
| GND | Ground wire | 故障灯ERROR | Error light |
| | SD 卡SD CARD | SD card slot |
Note: for TTL signal output, the controller must be ground supplied
to the luminaire (that is, connect the controller's ground output
to the luminaire's ground).
四 Wiring Method
Note:
1. T-1000B is single-port output, which can take up to 2048 pixels;
2. When controlling single-line IC, only the DAT and GND of the
controller are connected with the DAT and GND of the lamps and
lanterns.When controlling a two-wire IC, the controller's DAT.CLK
is needed
And GND and the lamp DAT,CLK and GND corresponding to the
connection.
3. When creating a new project in the effect editing software,
select the control model as T-1000B-IC
五 Special parameters
Memory card:
type:SD card(suggest using high-speed SD card)
Capacity:128MB—2GB
Format:FAT
Store file:*.led
Physical parameters:
Working temperature :-30℃—85℃
Working voltage:DC5V / DC7.5-24V
Working power:1W
size:L150mm×W71mm×H25mm
weight:0.35KG
signal port:3pin connect port
Note:
Before copy files to SD card ,The SD card must be formatted as FAT
format
The SD card in controller can not be hot-swappable, plug the SD
card every time, you must first disconnect the power supply
